Steel Plastic Geogrid for Stabilized Gravel Surface Subgrade for Reinforcement Net

Steel Plastic Geogrid Introduction:

Steel plastic geogrid mesh is made from high strength steel coated with virgin polyethylene or high density polyethylene by special ultrasonic welding and composite processing technology.  Steel plastic geogrid is weld into longitudinal and latitudinal staggered intervals in the same planner, different wire mesh diameter and root number can be fabricated according to project reinforcement force requirement. Due to reinforced steel biaxial geogrid combined with the regular rough pattern on the surface, the steel plastic geogrid mesh has great tensile strength, perfect corrosion resistance and excellent wear and tear resistance, etc. The stress and the friction between the soil and the fill generally limit the shearing of the foundation and the lateral extrusion bulge. The high rigidity of the reinforced soil cushion by the steel plastic geogrid mesh is beneficial to the diffusion of the upper foundation load and the uniform distribution. To the lower soft soil layer, the bearing capacity of the foundation is better improved. Due to the effect of the reinforced mat soil layer, the overall rigidity of the foundation within the compression layer is increased, which is beneficial to adjust the deformation of the foundation. Steel plastic geogrid reinforcement can effectively enhances the bearing capacity of foundation and prevents the soil from lateral displacement due to its high friction coefficient and the bearing capacity. The reinforced soil composite cushion formed with the help of the reinforced steel plastic geogrid mesh can even absorb the earthquake energy well, so its seismic performance is good.

Features: 

*High tensile strength and low distort and creep deformation

* Improving bearing capacity of road bed

* Anti-corrosion and extending the project life

* Shortening construction period,reducing cost.

Application:

1)Well pull: Longitudinal and crosswise tensile strength per linear meter can reach 30 to 120 KN.

2) Small deformation: the yield elongation of steel plastic integral geogrid is not bigger than 3%. 

3) Nodal point is high. 

4) Lifespan is long. It has the properties of anti – oxidation and anti – aging. It can be possible to meet each kind of 

permanent works and its lifespan can be 100 years above.

5) It can reduced the project cycle effectively and saved 10% to 50% of the building cost of projects. 

 6) The construction is convenient. It is easy to lay, join, locate and flat.

Technical Parameter :
High-strength steel plastic uniaxial (vertical) geogrid 

ProjectTGDG30TGDG50TGDG80TGDG100TGDG120TGDG150
  Vertically Limited-Rally
(KN/m)≥
305080100120150
Vertically Limited elongation ratio(%)≤333333
Elongation at 1% of the Rally  (KN/m)≥2338638198125

High-strength steel-plastic biaxial( vertical and horizontal) geogrid
 

ProjectTGSG30-30TGSG45-45TGSG60-60TGSG80-80TGSG100-100TGSG120-120
Two-way Limit-Rally
(KN/m)≥
30456080100120
Two-way Limit elongation
(%)≤
333333
Elongation at 1% of the
Rally   (KN/m)≥
233648638198

Geogrid  Advantage 

1. fast and an all-weather installation solution
2. construction of cost effective
3. Solutions for slope protection
4. Ability to reinforce any soil type 
5. Low creep under constant load
6. High modulus
7. Easy to install
8. High pull out resistance
9. Excellent survivability to construction stresses
10. Excellent soil-to-soil and aggregate-to-aggregate contact through large grid openings

FAQ
1, What is the difference between uniaxial and biaxial geogrid?
Biaxial geogrids are those that exhibit the same strength in both the machine directions MD and cross-machine directions CMD while uniaxial geogrids exhibit the primary strength in the machine direction with minimal strength, enough to maintain the aperture structure, in the cross-machine direction.

2, How many types of geogrids are there?
There are three different types of geogrids: Uniaxial, Biaxial, and Triaxial . Each one is designed and manufactured for specific construction applications with various tensile strengths.

3, Are you trading company or manufacturer?
We are factory.

4,Is the quality of your products stable?
The company has a complete QC system, and each batch of products will be sampled and the samples will be kept for 5 years.

5,Can you do OEM?
Yes, of course. We can produce the products as your request.

6, Do you provide samples? is it free?
Yes, we could offer the sample for free charge but do not pay the cost of freight.

7,How long is your delivery time?
Generally it is 5-10 days if the goods are in stock. or it is 10-15 days if the goods are not in stock, it is according to quantity.
   
8, What is your terms of payment?
Payment<=5000USD, 100% in advance. Payment>=30000USD, 30% T/T in advance,balance before shipment.

If you have another question, please feel free to contact us at any time.

Professional geosynthetics manufacturer
 Anhui Zhonglu Engineer Materials Co., Ltd

Leave a Comment

Your email address will not be published. Required fields are marked *